DSE157

The DSE157 is an output relay expansion module for use with DSEControl® and DSEPower® Series Modules (excluding DSE51xx). The DSE157 has been designed to extend a host modules output capabilities. The additional capabilities allow OEM’s to meet increasingly complex industry specifications. The module incorporates ‘DIN’ rail mountings and an interconnecting FCC 68 cable, allowing quick fixing into a panel. The module will work up to 50 meters from the host control module.

DSE130

The DSE130 is an input expansion system used to provide modules within the DSEControl® and DSEPower® Series (excluding the DSE51xx & DSE52xx) with additional analogue and digital input capabilities.

9B4T8

The DSE124 is a CANbus extender capable of extending either the Multiset Comms (MSC) Load Share Link or engine CANbus.

4 red LEDs provide indication of the module’s operational status.

Two variants are available:

1.     124-01. 

With fibre optic port.  This version can be used to provide a 2000m segment between two extenders with no reduction in

speed or number of modules that can be accommodated.

2.     124-02

Without the fibre optic port.  This version is used for applications where only the copper cable is required.

A maximum of 8 copper 250m segments and 2 fibre optic 2000m segments can be used together.

Both modules have been designed for DIN rail mounting or for fitting directly to the chassis.

DSE123

The DSE123 is a Load Share Lines Interface Device designed to expand existing analogue load share systems. The DSE123 monitors existing load share lines and converts the analogue information into a digital format. This process allows all existing control modules to communicate with the DSE7510 and DSE5510 control modules when they are added to the system.   When DC power is applied to the interface device a status LED will illuminate. If the DSE123 cannot communicate with the DSE7510 or DSE5510, the LED will flash to indicate a communication malfunction.   The device has been designed to work with both DSE and other manufacturers existing load share systems, providing that the system is being expanded with a DSE7510 or DSE5510.

DSEMarine DSE5510M

The DSE5510M is an Automatic Engine Control Module, designed to provide advanced load share functionality for diesel and gas generating sets that include non-electronic and electronic engines. The module also provides excellent engine monitoring and protection features.    The modules load share functions include, automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s). The module has been designed to combine a maximum of 16 generators and 16 mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4 mains (utility) supplies (DSE5560 required to synchronise with the mains)   The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.

Main Features	Electronic engine capability RS232 or RS485 remote communications Modbus RTU Pin number protected front panel programming Engine exercise timer Back-lit LCD 4-line text display Multiple language options Voltage measurement Configurable inputs (9) Configurable outputs (5) Automatic start Manual start Audible alarm LED indicators Built-in governor and AVR control Engine history event log Engine protection Fault condition notification to a designated PC Front panel mounting PC configuration Mains (utility) failure detection Configurable alarm timers Configurable start & stop timers Automatic load transfer SMS alert messaging Multi-set communications Front panel mounting Remote monitoring Magnetic pick-up Load Share Features Automatic starting & stopping of generator on load demand Automatic hours run balancing of generator sets Dead bus sensing Module has the ability to interface with existing load share systems Direct communication from the module to the governor and AVR Volts & frequency matching KW and Kvar load sharing with multiple generators ROCOF & vector shift
Benefits	Sends SMS messages to engineers to notify specific engine problems (GSM Modem & SIM Card required) On-site and remote module configuration In-built engine diagnostics removes the requirement for service equipment Full engine protection & instrumentation without the need for additional senders (Electronic engines only) Remote monitoring of the module using comprehensive DSE PC software License free PC software
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO and START pushbuttons. Three of these push buttons include an LED indicator.  Additional pushbuttons provide LCD display scroll, lamp test, mute functionality and breaker control.
Important Notes	THIS MODULE IS A SPECIAL MARINE VERSION FULLY CERTIFIED BY DNV FOR USE ON-BOARD VESSELS.  THE 'STANDARD' DSE5510 CANNOT BE USED FOR MARINE APPLICATIONS AS IT HAS NOT BEEN CERTIFIED.

DSEMarine DSE5310M

The DSE5310 is an Automatic Start Control Module designed to automatically start and stop diesel and gas generating sets that include non electronic and electronic engines. The module also provides advanced engine monitoring and protection features. 
The module has the ability to monitor under speed, over speed, charge failure, emergency stop, low oil pressure, high engine temperature, fail to start, fail to stop, under/over generator volts, over current, under/over generator frequency, low/high DC battery volts, low fuel alarm and loss of the speed sensing signal. The module displays fault conditions on the LCD display and via the LED indicators on the front of the panel.
The module also includes RS232 and RS485 communication capabilities for linking to a PC, sending SMS messages and interfacing with new and existing building management systems.

Main Features	Automatic start Electronic engine connection RS232 and RS485 remote communications Modbus RTU Analogue inputs Audible alarm indication Back-lit character & 4-line text LCD display Configurable alarms & timers Configurable auxiliary inputs Digital inputs Emergency stop functions Engine history event log Engine exercise mode Engine protection Front panel mounting Front panel programming Full engine diagnostics Generator operating status warning LCD alarm indication LED alarm indication Manual start Multiple language options PC configurable PIN protected programming Power save mode Remote monitoring SMS messaging
Benefits	Full integration into new & existing building management systems Full engine protection & instrumentation without the need for additional senders (Electronic engines only) In-built engine diagnostics removes the requirement for service equipment License free PC software Remote module control & monitoring using comprehensive DSE PC software Module improves the life cycle of engine starter motors On-site and remote module configuration Sends SMS messages to engineers to notify specific engine problems (GSM SIM required) User-friendly set-up and button layout
Operation	The module is operated using the front STOP, AUTO and MANUAL pushbuttons.    The DSE5310M also includes a TEST button. An additional pushbutton allows the user to scroll through the LCD display.
Important Notes	THIS MODULE IS A SPECIAL MARINE VERSION FULLY CERTIFIED BY DNV FOR USE ON-BOARD VESSELS.  THE 'STANDARD' DSE5310 CANNOT BE USED FOR MARINE APPLICATIONS AS IT HAS NOT BEEN CERTIFIED.

DSEPower DSE8721

THE DSE8721 COLOUR REMOTE DISPLAY  module is designed for use with the 8700 Rear Mounted Load Share Control module, giving a choice of display options suitable for a wide variety of applications. One (1) display module can be connected to one (1) DSE8700 control module via a data communication link up to a maximum distance of 1km.

This display module offers comprehensive large screen graphs, charts, metering, power display and engine status information in a clear image and text format in full colour.  Programming is via the front panel.

Main Features	FEATURES WHEN CONNECTED TO THE HOST MODULE – RS232 & RS485 remote communications – Audible alarm – Engine protection – Fault condition notification to a designated PC – Front panel mounting – Protected front panel programming – Configurable alarms and timers – Configurable start and stop timers – SMS alert messaging – Remote monitoring
Benefits	– Clear visual display in full colour, of all status information – Range of display options makes the system highly versatile to suit different load share application demands – Data communication link allows remote system management

DSEPower DSE8700

The DSE8700 is an easy-to-use, rear-mounted, multi-generator loadshare system, designed to synchronise up to 32 generators including electronic and non-electronic engines. The module is available in 2 variants:

– DSE8710 Auto Start (this can also be programmed for use as a DSE8760 Auto Mains Controller)

– DSE8760 ATS/Auto Mains Controller

The modules are designed to work with independent front display screens which are connected via a data link up to a maximum distance of 1km. These must be ordered as a separate item. The DSE8700 monitors the engine and indicates operational status and fault conditions, automatically starting or stopping the engine on load demand or fault condition.

Failures are annunciated on the independent front screens (multiple language options available), illuminated LEDs and audible sounder. The event log will record 250 events to facilitate easy maintenance. An extensive number of fixed and flexible monitoring, metering and protection features are included as well as sophisticated communication and system expansion options. Using the DSE PC Configuration Suite Software allows easy alteration of the operational

sequences, timers and alarms. With all communication ports able to be active at the same time, the DSE8700 is ideal for a wide variety of demanding load share applications.

 Main Features

 LOAD SHARE FEATURES

– Peak lopping

– Sequential set start

– Manual voltage/frequency adjustment

– ROCOF and vector shift

– Generator load demand

– Automatic hours run balancing

– Mains (Utility) de-coupling

– Dead bus sensing

– Mains (Utility) de-coupling test mode

– Bus failure detection

– Direct governor and AVR connections/controls

– Volts and frequency matching

– kW and kV Ar load sharing

 STANDARD FEATURES

– Independent display screen options

– Configurable inputs (11)

– Configurable outputs (8)

– Voltage measurement

– Built-in governor and AVR control

– kW overload alarms

– Comprehensive electrical protection

– Magnetic pick-up

– Electronic engine capability

– RS232 & RS485 remote communications

– Modbus RTU

– Multi event exercise timer

– Automatic start/Manual start

– Event log (250)

– Engine protection

– Fault condition notification to a designated PC

– PC configuration

– Configurable alarms and timers

– Configurable start and stop timers

– SMS alert messaging

– Remote monitoring

DSEPower DSE8680

The DSE8680 module is designed to control a bus-tie breaker, manage the synchronising and check-sync across the breaker and automatically control the DSE MSC (multi-set communications) link when opening or closing the bus-tie breaker. The DSE8680 module has been designed to work with DSE8610 and DSE8710 Load Share control modules which support up to 32 generators.

Main Features	KEY FEATURES Controls one bus-tie controller in a system containing DSE8610 and/or 8710 controllers Connects to two DSE MSC links, one for 'Bus1' and another for 'Bus 2' DSENet expansion capability LCD display for status and instrumentation Adjustable parameters via USB connection and DSE Configuration Suite PC software RS232 inerface for modem connection RS485 interface for BMS and PLC communications Manual (by button press) or automatic (by external signal) control of the bus-tie breaker 8 configurable outputs 11 configurable inputs
Benefits	KEY BENEFITS Allows the control of a bus-tie breaker Automatic synchronising across the bus-tie breaker Automatic control fo the DSE MSC link when the breaker is opened/closed Instrumentation shows the status and measurements of both generator buses
Alternative / Associated Products	DSE8610 - Auto Start Multi-Set Controller

DSEPower DSE8660

The DSE8660 is an easy-to-use single or multi-mains controller with automatic transfer switch capability.  Designed to synchronise single or multiple DSE8610s with single or multiple mains(utility) supplies, the DSE8660 will automatically control the change over from mains (utility) to generators in synchronisation with the mains (utility) to provide no-break, peak lopping and peak shaving power solutions.
The module can indicate operational status and fault conditions on the LCD screen (multiple languages available), by lit LED, audible sounder and SMS messaging.  Sophisticated communications are also available via RS485 and RS232 for remote PC control and monitoring and intigration into building management systems.  The comprehensive event log will record up to 250 events to facilitate easy maintenance.
An extensive number of fixed and flexible monitoring and protection features are included.  Easy alteration of the timers, sequences and alarms can be made using the DSE PC Configuration Suite Software.  Selected programming is also available via the module's front panel making the DSE8660 ideal for a wide variety of load share applications.

Main Features

LOAD SHARE FEATURES INCLUDE: Peak lopping Sequential set start Manual voltage/frequency adjustment ROCOF and vector shift Generator load demand Automatic hours run balancing Mains (Utility) de-coupling Mains (Utility) de-coupling test mode Bus failure detection Volts and frequency matching STANDARD FEATURES INCLUDE: Configurable inputs (11) Configurable outputs (8) Voltage measurement RS232 & RS485 remote communications Modbus RTU Multi event exercise timer Back-lit LCD 4-line text display Multiple display languages Automatic start/Manual start Audible alarm Fixed and flexible LED indicators Event log (250) Fault condition notification to a designated PC Front panel mounting Protected front panel programming PC configuration Configurable alarms and timers Configurable start and stop timers SMS alert messaging Remote monitoring

Benefits

BENEFITS RS232 & RS485 can be used at the same time DSENet connection for system expansion High number of inputs and outputs Worldwide Language Support Configuration Suite PC Software Direct USB connection to PC Ethernet monitoring*      USB Host* Data Logging & Trending*          * To follow

DSEPower DSE8610

The DSE8610 is an easy to use multi-generator loadshare system, designed to synchronise  up to 32 generators including electronic and non-electronic engines.

The DSE8610 monitors the engine and indicates operational status and fault conditions, automatically starting or

stopping the engine on load demand or fault condition.

Failures are annunciated on the LCD screen (multiple language options available), illuminated LED and audible sounder.

The event log will record 250 events to facilitate easy maintenance. An extensive number of fixed and flexible monitoring, metering and protection features are included as well as sophisticated communication and system expansion options.

Using the DSE PC Configuration Suite Software allows easy alteration of the operational sequences, timers and alarms.

With all communication ports able to be active at the same time, the DSE8610 is ideal for a wide variety of demanding load share applications.

Main Features

LOAD SHARE FEATURES INCLUDE:  Peak lopping Sequential set start Manual voltage/frequency adjustment ROCOF and vector shift Generator load demand Automatic hours run balancing Mains (Utility) de-coupling Mains (Utility) de-coupling test mode Dead bus sensing Bus failure detection Direct governor and AVR connections/controls Volts and frequency matching –  kW and kVAr load sharing STANDARD FEATURES INCLUDE: Configurable inputs (11) Configurable outputs (8) Voltage measurement Built-in governor and AVR control –  kW overload alarms Comprehensive electrical protection Magnetic pick-up Electronic engine capability  RS232 & RS485 remote communications Modbus RTU Multi event exercise timer Back-lit LCD 4-line text display Multiple display languages Automatic start/Manual start Audible alarm Fixed and flexible LED indicators Event log (250) Engine protection Fault condition notification to a designated PC Front panel mounting Protected front panel programming PC configuration Configurable alarms and timers Configurable start and stop timers SMS alert messaging Remote monitoring

Benefits

RS232 & RS485 can be used at the same time DSENet connection for system expansion PLC Functionality Auto Voltage Sensing Five Step dummy load support Five Step Load Shedding support High number of inputs and outputs Worldwide Language Support Configuration Suite PC Software Direct USB connection to PC Ethernet monitoring* USB Host* Data Logging & Trending* * To follow

DSEPower DSE8005

The DSE8005 SCADA Suite software for Windows PC enables remote control and monitoring of DSE load share systems comprising of DSE86xx and DSE87xx (to follow) modules.

The DSE8005 will monitor up to a maximum number of 40 DSE controllers in any combination of up to 32 generators and 10 mains(utilities) e.g. 30 generators + 10 mains, 32 generators + 8 mains etc.. For more information please refer to the 86xx or 87xx manual.

Modules are linked via a high-speed RS485 connection in a ‘daisy-chain’ topology

Main Features

Compatible with WIndows 7, XP and Vista, the software can be easily installed into any laptop or PC, allowing full remote control and monitoring facilities. The Windows based software is licence-free and user-friendly. FULL ON-SCREEN FUNCTIONALITY - Touch screen PC enabled - Engine start/stop - Monitoring and control - Switching on and off load - Load demand priority - Mains (Utility) base load power levels - 32/64-bit operating system

Alternative / Associated Products

DSE8610 - Auto Start Multi-Set Controller DSE8660 - Auto Transfer Switch and Mains Control Module DSE8700 - Rear Mounted Load Share module

DSEPower DSE7570

The DSE7570 Sync Lock Controller has been designed for manual connection and disconnection from the mains/utility supply.
The Sync Lock Controller provides a user-friendly zero-sync/phase locking solution, that is easily integrated with generators controlled by the DSE7510 Load Share modules. With forward and backward syncronising with the mains/utility supply, the DSE7570 is ideal for temporary generator installations.
Where access is restricted, the DSE Sync Lock Interface is used to provide up to a maximum distance of 200 m between the DSE7570 Sync Lock Controller and the DSE7510 Load Share module.

Main Features	TYPICAL APPLICATIONS Generator hire Local sub-station maintenance, service and repairs Emergency power provision Temporary power solutions
Benefits	KEY BENEFITS: No-break removal and return of mains/utility fuses Provides a user-friendly zero-sync/phase locking solution, ideal for temporary generator installations including forward and backward synchronising with mains/utility Interface provides application flexibility where access is limited

DSEPower DSE7560

The DSE7560 is an Automatic Transfer Switch and Mains Control Module, designed to automatically synchronise multiple DSE7510s with single or multiple mains (utility) supplies.  The module instructs the DSE7510s to make precise changes to the generating set outputs. This makes the module suitable for many applications including peak lopping, peak shaving and no break return.

The module has the ability to monitor the mains (utility) supply and start and stop the generating sets (being controlled by a DSE7510) upon removal or detection of the mains (utility) supply. The modules operational status is indicated on the LCD display and the front panel LEDs.

Main Features	• Multiple language options • Back-lit 4-line text LCD display • Configurable timers • Configurable inputs (9) • Configurable outputs (5) • Automatic hours run balancing • Peak lopping control for DSE7510 controlled generator bus • Peak shaving • No break return • PIN protected programming • Full remote control and telemetry • Mains (utility) fail monitoring • Load demand scheme • Multiple mains (utility) monitoring • System lock input • Load switching control pushbutton inputs • Engine history event log • LED indicators • PC configurable
Benefits	• On-site module configuration • Remote module configuration via PC software • In-built diagnostics removes the requirement for service equipment • Transfers between mains and generator • Remote control and monitoring of the module using comprehensive DSE PC software • License free PC software
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO, TEST and START push buttons. The first four of these push buttons include LED indicators. Additional push buttons provide LCD page display scroll, lamp test, mute and load switching functionality.

DSEPower DSE7520

The DSE7520 is an Automatic Mains Failure Control Module designed to provide advanced load share functionality for diesel and gas generating sets that include non electronic and electronic engines, for single set appications and parallel with mains. The module also provides excellent engine monitoring andprotection features. 

The module monitors the mains (utility) supply and, upon detection of a loss of power, automatically starts the generating set.

The module’s synchronizing functions include automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVRs). 

The module has the ability to monitor generator under/over generator volts, over current, under/over generator

frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync,MPU open circuit failure, negative phase sequence and loss of excitation.

Main Features

• Electronic engine capability • RS232 or RS485 remote communications • Modbus RTU • Pin number protected front panelprogramming • Exercise timer • Back-lit LCD 4-line text display • Multiple language options • Voltage measurement • Configurable inputs (9) • Configurable outputs (5) • Automatic start • Manual start • Audible alarm • LED indicators • Built-in governor and AVR controlfor easy operation and panelengineering • Engine history event log • Engine protection • Fault condition notification to a designated PC • Front panel mounting • PC configuration • Mains (utility) failure detection • Configurable alarm timers • Configurable start & stop timers • Automatic load transfer • SMS alert messaging • Multi set communications • Remote control and monitoring • Dedicated load test button • kW overload alarms • Engine temperature alarms • MV-LV synching LOAD SHARE FEATURES • No break transfer • Peak shaving/peak lopping • KW on mains level • Mains decoupling test mode • Manual speed/frequency adjust • ROCOF & vector shift • Dead bus sensing • Direct governor & AVR communication • Volts & frequency matching • KW and kVar load sharing • Manual voltage adjust

Benefits

• Sends SMS messages to engineers to notify specific engine problems (GSM Modem and SIM card required) • On-site and remote module configuration • In-built engine diagnostics removes the requirement for service equipment • Full engine protection & instrumentation without the need for additional senders (Electronic engines only) • Remote monitoring of the module using comprehensive DSE PC software • License free PC software • No-break return capability

DSEPower DSE7510

The DSE7510 is an Automatic Engine ControlModule, designed to provide advanced load share functionality for diesel and gas generating sets that include nonelectronic and electronic engines.  The module also provides excellent engine monitoring and protection features.

The module’s load share functions include, automatic synchronizing with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVRs).

The module has been designed to combine a maximum of 16 generators and 16mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4mains (utility) supplies (DSE7560 required to synchronise with the mains).  The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync,MPU open circuit failure, negative phase sequence and loss of excitation.

Main Features	• Electronic engine capability • RS232 or RS485 remote communications • Modbus RTU • Pin number protected front panel programming • Engine exercise timer • Back-lit LCD 4-line text display • Multiple display languages • Voltage measurement • Configurable inputs (9) • Configurable outputs (5) • Automatic start • Manual start • Audible alarm • LED indicators • Built-in governor and AVR control • Engine history event log • Engine protection • Fault condition notification to a designated PC • Front panel mounting • PC configuration • Bus failure detection • Configurable alarm timers • Configurable start & stop timers • Automatic load transfer • SMS alert messaging • Remote monitoring • Magnetic pick-up • KW overload alarms • Engine inlet temperature alarms  LOAD SHARE FEATURES • No break transfer • Peak shaving/peak lopping • Sequential set start • KW on mains level • Mains decoupling test mode • Manual speed/frequency adjust • ROCOF & vector shift • Generator load demand • Automatic hours run balancing • Dead bus sensing • Existing load share line interfacing (P123 required) • Direct governor & AVR communication • Volts & frequency matching • kW and Kvar load sharing • Manual voltage adjust • Auto MSC ID negotiation
Benefits	• Sends SMS messages to engineers to notify specific engine problems (GSM Modem and SIM card required) • On-site and remote (modem required) module configuration • In-built engine diagnostics removes the requirement for service equipment • Full engine protection & instrumentation without the need for additional senders (Electronic engines only) • Remote monitoring of the module using comprehensive DSE PC software • License free PC software
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO and START push buttons. Three of these push buttons include an LED indicator.  dditional push buttons provide LCD display scroll, lamp test, mute functionality and breaker control.
Important Notes	The module gives the user full telemetry facilities when using the optional communications software.  The module can be connected to a PC using the DSE810 PC interface or by using a suitable modem.  The PC software is Microsoft Windows™ based.  All access into the module can be configured to become password protected to prevent unauthorised entry. The PC software allows the module to be controlled from a remote location.

DSEPower DSE5560

The DSE5560 is an Automatic Transfer Switch and Mains Control Module, designed to automatically synchronise multiple DSE5510’s with single or multiple mains (utility) supplies. The module instructs the DSE5510’s to make precise changes to the generating set outputs. This makes the module suitable for many applications including peak lopping, peak shaving and no break return.   The module has the ability to monitor the mains (utility) supply and start and stop the generating sets (being controlled by a DSE5510) upon removal or detection of the mains (utility) supply. The modules operational status is indicated on the LCD display and the front panel LED’s.

Main Features	Multiple language options Back-lit 4-line text LCD display Configurable timers Configurable inputs (9) Configurable outputs (5) Automatic hours run balancing Peak lopping control for DSE5510 controlled generator bus Peak shaving No break return PIN protected programming Full remote control and telemetry Mains (utility) fail monitoring Load demand scheme Multiple mains (utility) monitoring System lock input Load switching control push-button inputs Engine history event log LED indicators PC configurable
Benefits	On-site module configuration Remote module configuration via PC software In-built engine diagnostics removes the requirement for service equipment Full engine protection & instrumentation without the need for additional senders Remote control & monitoring of the module using comprehensive DSE PC software License free PC software Transfer’s between mains and generator power
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO, TEST and START pushbuttons. The first four of these push buttons include LED indicators. Additional pushbuttons provide LCD page display scroll, lamp test, mute and load switching functionality.
Important Notes	Below are links to some helpful documents regarding synchronisation and load sharing : Load Share System Design and Commissioning Guide Guide to Synchronising and load sharing part 1 Guide to Synchronising and load sharing part 2
Alternative / Associated Products	DSE5510 - Auto Start Control Module (Electronic engine enabled) DSE5520 - Auto Mains Failure & Instrumentation Control Module (Electronic engine enabled) DSE123 - Load Share Lines Interface DSE7560 - Auto Transfer Switch & Mains (Utility) Control Module DSE8660 - Auto Transfer Switch and Mains Control Module DSE8700 - Rear Mounted Load Share module

DSEPower DSE5520

The DSE5520 is an Automatic Mains Failure Control Module designed to provide advanced load share functionality for diesel and gas generating sets that include non electronic and electronic engines. The module also provides excellent engine monitoring and protection features.    The module monitors the mains (utility) supply and upon detection of a loss in power automatically starts the generating set.   The modules synchronising functions include automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s).  The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.

Further Information

Main Features	Electronic engine capability RS232 or RS485 remote communications Modbus RTU Pin number protected front panel programming Engine exercise timer Back-lit LCD 4-line text display Multiple language options Voltage measurement Configurable inputs (9) Configurable outputs (5) Automatic start Manual start Audible alarm LED indicators Built-in governor and AVR control for easy operation and panel engineering Engine history event log Engine Protection Fault condition notification to a designated PC Front Panel Mounting PC configuration Mains (utility) failure detection Configurable alarm timers Configurable start & stop timers Automatic load transfer SMS alert messaging Multi-set communications Remote monitoring and control Load Share Features  Automatic starting and stopping of generator on load demand Direct communication from the module to the governor and AVR  Volts and frequency matching KW and Kvar load sharing with multiple generators ROCOF and vector shift
Benefits	Sends SMS messages to engineers to notify specific engine problems (GSM Modem and SIM Card required) On-site and remote module configuration In-built engine diagnostics removes the requirement for service equipment Full engine protection & instrumentation without the need for additional senders (Electronic engine only) Remote monitoring of the module using comprehensive DSE PC software License free PC software
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO and START pushbuttons. Three of these push buttons include an LED indicator. Additional pushbuttons provide LCD display scroll, lamp test, mute functionality and breaker control.
Important Notes	Below are links to some helpful documents regarding synchronisation and load sharing : Load Share System Design and Commissioning Guide Guide to Synchronising and load sharing part 1 Guide to Synchronising and load sharing part 2

DSEPower DSE5510

The DSE5510 is an Automatic Engine Control Module, designed to provide advanced load share functionality for diesel and gas generating sets that include non-electronic and electronic engines. The module also provides excellent engine monitoring and protection features.    The modules load share functions include, automatic synchronising with built in synchroscope and closing onto dead bus. Direct and flexible outputs from the module are provided to allow connection to the most commonly used speed governors and automatic voltage regulators (AVR’s). The module has been designed to combine a maximum of 16 generators and 16 mains (utility) supplies up to a maximum of 20 in one system, e.g. 16 generators and 4 mains (utility) supplies (DSE5560 required to synchronise with the mains)   The module has the ability to monitor under/over generator volts, over current, under/over generator frequency, under speed, over speed, charge fail, emergency stop, low oil pressure, high engine temperature, fail to start, low/high DC battery volts, fail to stop, generator short circuit protection, reverse power, generator phase rotation error, earth fault protection, loss of speed signal, fail to open, fail to close, out of sync and MPU open circuit failure, negative phase sequence and loss of excitation.

er Information

Main Features	Electronic engine capability RS232 and RS485 remote communications Modbus RTU Pin number protected front panel programming Engine exercise timer Back-lit LCD 4-line text display Multiple language options Voltage measurement Configurable inputs (9) Configurable outputs (5) Automatic start Manual start Audible alarm LED indicators Built-in governor and AVR control Engine history event log Engine protection Fault condition notification to a desginated PC Front panel mounting PC configuration Mains (utility) failure detection Configurable alarm timers Configurable start & stop timers Automatic load transfer SMS alert messaging Multi-set communications Remote monitoring Magnetic pick-up Load Share Features  Automatic starting & stopping of generator on load demand Automatic hours run balancing of generator sets Dead bus sensing Module has the ability to interface with existing load share lines Direct communication from the module to the governor and AVR Volts & frequency matching KW and Kvar load sharing with multiple generators ROCOF & vector shift
Benefits	Sends SMS messages to engineers to notify specific engine problems (GSM Modem & SIM Card required) On-site and remote module configuration In-built engine diagnostics removes the requirement for service equipment Full engine protection & instrumentation without the need for additional senders (Electronic engines only) Remote monitoring of the module using comprehensive DSE PC software License free PC software
Operation	The module is operated using the front STOP/RESET, MANUAL, AUTO and START pushbuttons. Three of these push buttons include an LED indicator.  Additional pushbuttons provide LCD display scroll, lamp test, mute functionality and breaker control.
Important Notes	Below are some helpful documents regarding synchronisation and load sharing and electronic engines : Load Share System Design and Commissioning Guide Guide to Synchronising and Load Sharing Part 1 Guide to Synchronising and Load Sharing Part 2 Electronic Engines and DSE Wiring

DSEPower DSE871x

The Mono Remote Display module offers 4-line text and icon information for use with DSE8700 Rear Mounted Load Share module.
One (1) display module can be connected to one (1) DSE8700 control module via a data communication link up to a maximum distance of 1km (on RS485)

Main Features	FEATURES WHEN CONNECTED TO THE HOST MODULE – RS232 & RS485 remote communications – Audible alarm – Engine protection – Fault condition notification to a designated PC – Front panel mounting – Protected front panel programming – Configurable alarms and timers – Configurable start and stop timers – SMS alert messaging – Remote monitoring
Benefits	– Clear text and icon display, of all status information – Data communication link allows remote system management
Alternative / Associated Products	DSE8700 - Rear Mounted Load Share module DSE8721 - Colour Remote Display

DSEPower DSE850

• Deep Sea Electronics DSE850 Multi-Set Communications Hub and Software has been designed to work with the DSEPower Series Load Share Control Modules (DSE55xx and DSE75xx). The software is scheduled to be compatible with additional DSE controllers in the near future.
  The DSE850 Ethernet controller is connected to the internet and all DSE control modules that are on-site. The Ethernet controller requires a fixed internal IP address that can be configured to be visible over the internet (using a third party external router).  Once the IP address can be accessed over the internet then sites can be viewed from any internet connection in the world.
  The system has been designed to display information on a maximum of 16 gen-sets and 4 mains (utilities) or 24 gen-sets with no mains (utilities). The software is easy to set up and DSE controllers can easily be added to the system using the software’s intuitive ‘Add Controller’ page.
  The Ethernet device includes RS232 and RS485 communications ports.  The data taken from the DSE controllers is refreshed every 1-11 seconds (dependent on connection speed).
  
  

  Main Features

  Clear alarms & re-start generators Multiple password levels (Read only, minor changes, full control) ·  Log into system from any web connection (using third party external router) Multi or single set compatible Easy to use graphical interface       System overview screen with instant status indication of gen-sets         Fully detailed controller screens  User configurable data logging       Logs can be downloaded to a local computer for importing data into spreadsheets Alarms with multiple trigger levels RS232 and RS485 communications ports       Common screen layouts for ease of use     E-mail support      Remotely upgradeable firmware       Controller communication log page     Colour engine status indicators – Blue = At rest, Green = Running OK, Grey = Lost contact, Yellow = Warning alarm, Red = Shutdown    Software can display site names on each page for easy identification

  Benefits

  View site status quickly and easily System can send email notification in the event of a change in engine status, engine warning or engine shutdown to a defined email address (using third party external router) Alarms can be cleared and generators re-started (If no site maintenance is required) Software can be used to identify trends in engine behaviour Allows multiple sites to be monitored from one location (Each site needs its own IP address) Full module control Gives information for basic fault finding diagnosis before attending site Can be used on an intranet site for monitoring internally

DSEControl DSE7320

The DSE7320 is a generator controller for single gen-set applications. The module incorporates a number of advanced features to meet the most demanding on-site applications.  The DSE7320 is an Auto Mains (Utility) Failure Generator Control Module designed to start and stop diesel and gas generating sets that include electronic and non-electronic engines. The DSE7320 includes the capability of being able to monitor a mains (utility) supply.

Generator Control Modules include USB, RS232 and RS485 ports as well as dedicated DSENet® terminals for expansion device connectivity. The Generator Controller are simple to operate and feature a simple menu layout for improved clarity. Enhanced features include a real time clock for enhanced event and performance monitoring, Ethernet communications for low cost monitoring, and preventative maintenance features to detect engine part faults prior to a major problem occuring.

Main Features	NEW FEATURES • Neutral position on breakers • Mains current protection • Improved mains detection 3phase 3 wire • Improved modem diagnostics • Remote control sources (10) can be accessed via SCADA • Additional electrical trip options • Additional start delay functions • Oil pressure values from additional engines • Front panel editing of scheduler • Now displays kW as % of rated kW setting • Additional programmable logic STANDARD FEATURES • Backed up real time clock • Ethernet communications • Multiple date and time maintenance scheduler • 132 x 64 pixel LCD display • Configurable display languages • Programmable event logging (250), showing reason, date and time • Robust module enclosure • Five key menu navigation • Durable soft touch membrane buttons • Fully configurable via PC software • LED and LCD alarm indication • Engine exercise mode • Configurable start & fuel outputs • kWh monitoring • Automatic load transfer • Configurable inputs • Configurable outputs • Configurable timers and alarms • Modbus RTU • Magnetic pick-up • Selected front panel programming • Multiple date and time exercise scheduler • Configurable display pages • Programmable load shedding/acceptance • Mutual standby • Preventative maintenance • kW overload protection • 3 alternative configurations • Unbalanced load protection • SMS messaging (external modem required) • Power save mode • PIN protected programming • Configuration file downloads from an external memory device • RS232 & RS485 communications • DSENet® compatible
Benefits	• 132 x 64 pixel ratio makes information easy to read • Real time clock provides accurate event logging • PC software is license free • Set maintenance periods can be configured to maintain optimum engine performance • Ethernet communications provides advanced remote monitoring at low cost • Modules can be integrated into building management systems • Preventative maintenance avoids expensive engine down time • Advanced PCB layout ensures high reliability
Operation	The modules are operated via the START, STOP, AUTO and MANUAL soft touch membrane buttons on the front panel. The DSE7320 also has a TEST button. Both modules include load switch buttons. The main menu system is accessed using the five navigation buttons to the left of the LCD display.
Important Notes	To view the UL listing for this product, please click on the link underneath and within the Company Name search field, type Deep Sea Electronics.  Our full UL classification will then appear.

DSEControl DSE7310

The DSE7310 is a control module for single gen-set applications. The module incorporates a number of advanced features to meet the most demanding on-site applications.  The DSE7310 is an Automatic Start Control Module designed to start and stop diesel and gas generating sets that include electronic and non-electronic engines. The module includes USB, RS232 and RS485 ports as well as dedicated DSENet® terminals for expansion device connectivity. The modules are simple to operate and feature a simple menu layout for improved clarity. Enhanced features include a real time clock for enhanced event and performance monitoring, Ethernet communications for low cost monitoring, dual mutual standby to reduce engine wear and tear, and preventative maintenance features to detect engine part faults prior to a major problem occuring.

Main Features	NEW FEATURES • Neutral position on breakers • Mains current protection • Improved mains detection 3phase 3 wire • Additional programmable logic • Improved modem diagnostics • Remote control sources (10) can be accessed via SCADA • Additional electrical trip options • Additional start delay functions • Oil pressure values from additional engines • Front panel editing of scheduler • Now displays kW as % of rated kW setting STANDARD FEATURES • Backed up real time clock • True dual mutual standby with load balancing timer • Ethernet communications • Multiple date and time maintenance scheduler • 132 x 64 pixel LCD display • Configurable display languages • Programmable event logging (250), showing reason, date and time • Robust module enclosure • Five key menu navigation • Durable soft touch membrane buttons • Fully configurable via PC software • LED and LCD alarm indication • Engine exercise mode • Configurable start & fuel outputs • kWh monitoring • Automatic load transfer • Configurable inputs • Configurable outputs • Configurable timers and alarms • Modbus RTU • Magnetic pick-up • Selected front panel programming • Multiple date and time exercise scheduler • Configurable display pages • Programmable load shedding/acceptance • Mutual standby • Preventative maintenance • kW overload protection • 3 alternative configurations • Unbalanced load protection • SMS messaging (external modem required) • Power save mode • Security levels - PC software has password system to control access to PC software features • Configuration file downloads from an external memory device • RS232 & RS485 communications • DSENet® compatible • Mains current protection
Benefits	• 132 x 64 pixel ratio makes information easy to read • Real time clock provides accurate event logging • PC software is license free • Set maintenance periods can be configured to maintain optimum engine performance • Ethernet communications provides advanced remote monitoring at low cost • Modules can be integrated into building management systems • Preventative maintenance avoids expensive engine down time • Advanced PCB layout ensures high reliability
Operation	The modules are operated via the START, STOP, AUTO and MANUAL soft touch membrane buttons on the front panel ands include la oad switch button. The main menu system is accessed using the five navigation buttons to the left of the LCD display.
Important Notes	To view the UL listing for this product, please click on the link underneath and within the Company Name search field, type Deep Sea Electronics.  Our full UL classification will then appear.

DSEControl DSE7220

The DSE7220 is a control module for single gen-set applications. The module incorporates a number of advanced features to meet the most demanding on-site applications. The DSE7220 is an Auto Mains (Utility) Failure Control Module designed to start and stop diesel and gas generating sets that include electronic and non-electronic engines. The module has the capability of being able to monitor a mains (utility) supply. Modules are simple to operate and feature a user-friendly menu layout for improved clarity. Enhanced features include a real time clock for improved event and performance monitoring, the ability to display any language on screen and a 132 x 64 pixel LCD display.

Main Features	NEW FEATURES • Additional programmable logic • Additional electric trip options • Additional start delay functions • Oil pressure values from additional engines • Front panel editing of scheduler • Displays kW as % of rated kW setting STANDARD FEATURES  • Backed up real time clock • 132 x 64 pixel LCD display • Configurable display languages • USB connectivity • Five key menu navigation • Fully configurable via PC software • Front panel editor • LED and LCD alarm indication • Engine exercise mode • Configurable start & fuel outputs • kWh monitoring • Automatic load transfer • 9 Configurable inputs • 6 Configurable outputs • Configurable timers and alarms • Magnetic pick-up • Power save mode • PIN protected programming • Improved programmable event logging (100), showing date and time • Manual fuel pump control • Manual speed control • Alternative configuration • Multiple date and time maintenance scheduler • 3 programmable maintenance alarms • Customisable status screens • Low fuel level alarm • Charge alternator fail warning and shutdown alarms with user programmable delay • Sleep mode • Load switching (Load shedding and dummy load outputs) • Manual speed trim (on CAN engines that support this feature) • Configurable SCADA output page • Security levels - PC software has password system to control access • Fan control for additional cooling • 'Protections Disabled' facility • Fuel useage monitoring and low fuel alarm • Support for up to 3 remote display units • Easy access, configurable diagnostics page shows summary of output states
Benefits	• 132 x 64 pixel ratio makes information easy to read • Real time clock provides accurate event logging • PC software is license free • Set maintenance periods can be configured to maintain optimum engine performance • Advanced PCB layout ensures high module reliability
Operation	The modules are operated via the START, STOP, AUTO and MANUAL soft touch membrane buttons on the front panel. The DSE7220 also has a TEST button. Modules include load switch buttons. The main menu system is accessed using the five navigation buttons to the left of the LCD display.
Important Notes	To view the UL listing for this product, please click on the link underneath and within the Company Name search field, type Deep Sea Electronics.  Our full UL classification will then appear. http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.html Below is a link to a helpful document regarding electronic engines : Electronic engines and DSE Wiring